Home > 80% Lowers > AR-15 80% Lower Receivers >

Engraved 80% Lower - AR-15 Forged 7075-T6 - Black Anodized

Engraved AR-15 80% Lower - Forged 7075-T6 - Black Anodized


 
Alternative Views:


Our 80% Lower Serial Number Engraving meets or exceeds the minimum requirements of the ATF, pertaining to the marking of a firearm receiver. All engraving is completed with a powerful laser engraver, well beyond the minimum required engraving depth.

You will receive:
- (1) AR-15 Forged 7075-T6 80% Lower Receiver
- Type III, Class 2 Black Anodized per MIL-A-8625
- Engraved beyond minimum depth of .003"
- Print size in excess of 1/16"

NOTE: Marking or engraving your 80% lower with a serial number is not required in any state, except for California when AB 857 takes effect on July 1, 2018. Serial number engraved 80% lowers are available to residents of any state, which again, is optional for residents outside California. Residents outside of California may wish to voluntarily mark the receiver frames in the event of loss or theft.

For California Residents: On July 1, 2018, California AB 857 will go into effect, requiring California residents who wish to comply, to have marked any home-built firearms per the ATF's minimum requirements for firearm marking and identification.

California AB 857 states that homemade firearms must be marked by July 1, 2018 in compliance with minimum requirements set forth by the ATF. Failure to mark home-built 80 percent lowers by July 1, 2018 will result in the need to apply to the state Department of Justice for a serial number, thereby registering the serial number and firearm. Buy your 80% Lowers Pre-Engraved now, before AB 857 takes effect.


INSTRUCTIONS:

In the form field below, please enter the following information:

NAME: The full (first and last) name of the person who will finish the 80% lower receiver. Initials and abbreviations are not acceptable. Acceptable: John Smith Not Acceptable: J. Smith
CITY: The City or Town where the person completing the firearm currently resides.
STATE: The 2-letter abbreviation of the state where the person completing the firearm currently resides.
SERIAL NUMBER: Enter your personalized serial number. NO SPACES. Alphanumeric characters only - 0-9, A-Z. Maximum of 8 characters. Enter only your desired serial number, every serial number will begin with S/N:. No obscenities, please.

If you wish to purchase multiple engraved 80% lowers, add to your shopping cart 1 at a time, re-entering the required information for each. Each serial number must be unique and cannot match any other home-built firearms serialized under your name! 5D Tactical does not store customer inputted serial numbers!

Notes: The engraving print and spacing may vary depending on the length of your city and/or name. "Cal: Multi" will be applied to all receivers, we are not able to accommodate custom caliber requests at this time. All engraving is completed after the hard coat anodizing process. Engraved 80% Lower orders may not be canceled, returned or exchanged.

*An 80% lower receiver is not considered a firearm and can be shipped directly to your home, no FFL needed. Finish with our AR-15 80% Lower Jig. Add a Stripped AR-15 Forged Upper Receiver for $54.99!

Select option below to add a Mil-Spec AR-15 Lower Parts kit to your order, or visit this page: AR-15 Lower Parts Kit






Price: $89.99
Sale Price: $79.99
You Save: $10.00


Product Code:
5D-AR15-7075F-BL-ENGR

Lower Parts Kit

Add Lower Parts Kit?:
AR-15 Mil-Spec Lower Parts Kit [Add $59.99]
Engraving

NAME*:


CITY*:


STATE*:


SERIAL NUMBER [A-Z, 0-9]*:


Qty:  
Description
 
In 2016, California Lawmakers passed AB 857 pertaining to firearm identifying information. This bill specifically targets homemade firearms finished from 80% lower receivers, and will take effect on July 1, 2018. In order for compliance, and to potentially avoid future registration, all homemade firearms must be marked by July 1, 2018. California has adopted the minimum requirements of the ATF for firearm identification. Therefore, all serial numbers and markings applied to homemade firearms must be conspicuously applied and meet the minimum following requirements:

1. Manufacturer Name: In this case, the manufacturer is the individual who completes the 80% lower. This must be the full name of the person who will finish the 80% lower.

2. Location: The home city and state of the individual who will finish the 80% lower.

3. Caliber Designation: With greater than 50 widely utilized AR-15 platform calibers, we will apply CAL-MULTI to the receiver to satisfy this requirement.

4. Serial Number: Serial numbers must be Alphanumeric (0-9, A-Z) characters only. NO SPACES. No special or foreign characters.

5. Depth and Size: Per the ATF, all engraving must be to a depth greater than .003 and no smaller than 1/16" of an inch. Our engraving will exceed the minimum depth and size.

Failure to apply compliant markings to homemade firearms by July 1, 2018 is not recommended, as it will result in the need for applying to the CA DOJ for a serial number and paying a fee. Starting January 1, 2019 the CA DOJ will begin accepting applications for the issuance of serial numbers for any homemade firearm which does not bear a compliant marking as of July 1, 2018.